Overshoot spec for OMAPL138 inputs
We have a signal driving pin C19 of OMAPL138 which overshoots/undershoots and violates theabsolute maximum voltage limits, but its duration is well within the time limit.The question is this: can the...
View ArticleClik here to view.
Execution time delay between PRU GPIO signals in C6748
Hello,I'm using the PRU0 in the TMS320C6748 DSP. The PRU clock is running at 150MHz. I'm trying to trigger a GPO (R30.31) signal out of PRU based on the rising edge of the input GPI (R31.4) signal. The...
View ArticleOMAP L138 IPC example with SYS-BIOS
Hi,I am trying to build an example of IPC (Notify (ARM)) with Logic evaluation board (OMAP 138 Soc) through SYS-BIOS v6.Once I build the project in CCS V6 I start getting these errors.Description...
View ArticleRE: Convert .out to hex file
Thanks Shankari for the reply. I am able to convert the files to the hex formats. But i am unable to pass control from one application to another. Would you be able to help me understand how can i do...
View Articlefor russia avaliable some primitive
hallow/ in rusia still uses L138. we bye a chip EVM without LCD and audio codec here inmys.ru/.../15226232
View ArticleHow to load arm to dsp interrupt example as an executable in Linux on...
I was able to get the ARM2DSP_integration example to build using code composer, but it will only boot when the board is in u-boot before it goes into linux. How would I create an executable or kernel...
View ArticleOMAP L137 Gel files
Hi,I have a custom board designed with OMAP L137 High Temp Chip, and I need a Gel file specific to OMAP 137 so I can modify it to change the boot mode when I use the JTAG xds200 to boot in NOR Flash...
View ArticleClik here to view.
GPIO BANK INTERRUPT
BOARD : OMAP-L138TOOL : CCS v3.3pspdrivers_01_30_00_06dspbios : 5.33.06I want to use GPIO bank interrupt.this is bank8 pin8 interrupt init function.and this is bank interrupt block.I connect function...
View ArticleClik here to view.
ccs5.2 gel file DDR initialization error
My cpu is omapl138 , when the gel file is load,some error occur:Please help me ! thank you.
View ArticleAM1808 - Cannot set SFH flash block number
Hi,My issue is how to set the block number of the NAND flash where the SFH program (v2.40) should store u-boot.bin.My NAND partitioning is #: name size offset...
View ArticleTestbed Selection
To whom it may concern,Is it possible to use the "USB2.0 XDS510 TI DSP JTAG Emulator Programmer" ($95.00) with the OMAPL138?Is it needed an external emulator for working with the TMDXLCDK6748...
View ArticlePHY Read Unsuccessful(OMAPL138 MDIO + Micrel PHY)
Hi there,I am trying to bring up the ethernet port on a custom board with OMAPL138 ARM processor and Micrel KSZ8081RNB1A PHY. The PHY address lines are connected to ground (Hence I am usnig 0 as phy...
View ArticleI have a question about omapl138. I want to change the frequency about the...
1 Can I only modify the linux kernal source code about this ? If it was,where could I change?2 I have a project about UBL which I can open in CCS3.3. Can I compile it in CCS3.3 and then load it into...
View ArticleC674x McBSP with FIFO and DMA delay
We have configured McBSP to use FIFO and linked EDMA to handle the transfers. Buffer size is 64 byte. Data transfer is happening between two c674x processors. No loss of data or errors observed in...
View ArticleCamera Selection for TMDXLCD6748 and OMAPL138
To whom it may concern, We plan to work with:TMDXLCDK6748 and USB2.0 XDS510 TI DSP JTAG Emulator Programmer, and OMAPL138 and USB2.0 XDS510 TI DSP JTAG Emulator Programmer Regarding cameras,...
View ArticleTMDXLCDK138
Hi,Can not find TMDXLCDK138 from TI or distributors, is this temporary situation or is there excisting or coming a replacing kit? I have eXperimenter from LogicPD but TI's MCSDK does not support it...
View ArticleARM to ARM interrupt with CHIPSIG
Dear AllCould, i trigger interrupt with CHIPSIG, e.g. CHIPSIG3 inside the ARM and then, create the ISR also in ARM side.e.g.# define ARM_TO_ARM_DATA_IRQ 31# define CHIPSIG...
View ArticleClik here to view.
I2C driver problem
Hi,I use CCS 6.0.1, DSP/BIOS 5.42.1.09, processor OMAP-L138 (DSP only), C6748 BIOS PSP 01.30.01.At execution of the following commands:wBuffer [0] = 0x07u; dataBuffer.slaveAddr = 0xECu;...
View ArticleBIOS drivers for L138
Hello!, I am new to the SYS/BIOS RTOS Environment, I have installed a mcsdk (BIOSLINUXMCSDK-OMAPL13X) fromhttp://software-dl.ti.com/sdoemb/sdoemb_public_sw/mcsdk/latest1/index_FDS.html link, which...
View ArticleAM1705 Boot from NAND Flash
Hello Guys,i am quite new to TIs Cors and CCS so just some short questions:I wrote a little programm and succesfully compiled it. So there is a .out and .hex File available.Boot Pins are set to NAND...
View Article