using startware 1_10_04_01 for OMAP-L138.
Hi everyone,I am using startware 1_10_04_01 for OMAP-L138. I got a compiling error "warning: function "ASSERT" declared implicitly".I did a serch in startware 1_10_04_01 folder, but I did not find this...
View ArticleOMAP-L138_FlashAndBootUtils_2_40\OMAP-L138\CCS\NANDWriter doesnt work
i have got the flash problem when using the "OMAP-L138_FlashAndBootUtils_2_40\OMAP-L138\CCS\NANDWriter";soc :AM1808ccs6.01first using the raw NANDWriter prject ,load the NANDWriter_ARM.out ,but it...
View ArticleClik here to view.
TI-RTOS for arm9 ?
Hello,I am not sure if arm can also be used with TI-RTOS.Does TI-RTOS support using arm ?If yes - will it support all the driver listed in for arm:EMAC. Ethernet driver used by the networking stack...
View Articleam1705 uboot build
Hello,Can anyone tell me how can I build uboot for my custom board? The information available is confusing. Please help.Where to start?I'm watching the Sitara Linux Board Porting Series but this...
View ArticleReceive data from McBSP1 of OMAP L138 LCDK
Dear Friends,I would like to better understand how to use the MCBSP module of our OMAP L138 LCDK. I've already run the mcbspSampleMaster example which is available at this directory:...
View ArticleClik here to view.
Which ARM compiler to use to design on OMAPL138?
Hi there,I have recntly board the OMAPL138 LCDK kit and trying to run few examples to learn about the use of ARM and the DSP cores. I am familiar with the DSP side of code but not very much with the...
View Articlesend event notification using IPC on OMAP-L138
Hi everyone,I am using IPClite from startware_01_10_04_01 on my omap-l138. Can I send two event notification from DSP to RAM when interrupt model is used. do I need to wait for the interrupt to ARM...
View ArticleOmap Setup questions
I am moving from a C6748 to an omap L-138 so I can leverage the ARM for extra processing power. I read the documentation on booting up both processors. That is rather straightforward. After they...
View ArticleClik here to view.
OMAPL-132 Nand question
Hi.We have a custom OMAPL-132 board with Micron NAND MT29F1G08ABBDAHC. On some of our boards we encountered nand read and bad blocks failures. We currently have the nand partitioned with UBIFS, JFFS2...
View ArticleVPIF capture from composite in through vpif_mmap_loopback on OMAP-L138 LCDK
I've configured and build linux kernell for OMAP L138, as it describes here: http://processors.wiki.ti.com/index.php/MCSDK_OMAPL138_User_Guide_Chapter_Exploring#OverviewThen I'm build examples for...
View ArticleOMAPL-138 UART Communication Issue
Hi, I am using OMAPL-138 package in my project. I configured UART channels on DSP core as per below settings. I am using OMAPL_138_StarterWare_1_10_04_01.// UART Settings...
View ArticleAM1705 Gel Script Error
Hi,I've designed a custom board using an AM1705 hopefully running Linux. I however am struggling to program my board with the NANDWriter utility used for programming the NAND flash. I've managed to...
View ArticleCache l2
HelloI am using lcdkc6748 with face detection demonstration. When I try to enable the l2 cache in the platform file i get problems with the display. I use DDR for data program and stack memory and...
View ArticleCompiling ARM code
I have an Omap L-138. I have code for the C6748 that compiles fine. I have another project in CCS 5.5 for the ARM. I am getting errors when compiling the ARM code. When I include <std.h> I...
View ArticleClik here to view.
AM1808 Quad Uart TL16CP554
Hi,I have interfaced Quad Uart TL16CP554 with AM1808 on EMI lines, when i boot "LOOP test failed", please help me in rectifying this issue.source code attached.(Please visit the site to view this...
View ArticleOMAPL138B-EP reliability
Type OMAPL138B-EP is specified at a maximum Tj of 125°C.TI specifies a Power-ON lifetime of maximum 29145 hours at Tj=125°C in the datasheet.However the application reports SPNA207 (incl spreadsheet)...
View ArticleLoad program Error. Load Failed for Omap-L138 LCDK
I compiled the IPC starterware code for the ARM and DSP. I can load and run the DSP code on the LCDK without a problem. When I try to load the ARM code on the board I get a Load Program Error....
View ArticleDSP code not running when boot in NADA mode but works fine when load using...
Hi everyone,my dsp code works fine on OMAP-L138 using emulator, but not running when boot from NADA if the section in red is in L2. If I move it to DDR2, then it works. what could be the issues? my...
View ArticleAM1705 Serial Flash and Boot utils build failing
Hello,I have several doubts regarding the Serial Flash and Boot utils. My questions are the following:I'm using the OMAP-L137_FlashAndBootUtils_2_40 version.1) How do I know if I need to rebuild the...
View ArticleOMAP-L138 VPIF driver error registering v4l2 subdevice
I'm trying to configure VPIF driver for video capture from analog camera, connected through composite-in on my OMAP-L138 LCDK board.I've configured menu config like...
View Article