SharedRegion
............................................1.it can't write immediately to shared ram.code list delow:static bool server_upp_data_transfer(Server *server) { if(server->ad_started == false) return...
View ArticleSM28VLT32-HT SPI flash device on OMAP-l137
Hello All, Am using OMAPL-137 in my project for high temperature application. Also, to program the bin file to flash memory am using SM28VLT32SHKN device. Basically i want the boot my...
View ArticleTMS320C6743 External Memory Interface
HelloI am Alber as a FAE in Arrow Korea.My customer asked about TMS320C6743.There was written following at datasheet page 64.----------------------------------------------------------------------6.10.1...
View ArticleRegarding how to boot arm processor in Omapl138
hi,i am using Omapl138 (LCDK) board i need to boot ARM processor will you please suggest where can i download booting image and switch configuration to boot from SDcard and how to access GPIO and...
View ArticleHow to Run application code after flashing to NAND Flash?
Hi there, I am build the client example provided with the NSP 1_10_00_03 and it works fine but when I tried to flash the *.bin file the example does seem to run. I have converted the *.out file to...
View Articlebooting image
where can i find booting image for OPMAPL138 i lost SD card that comes with board
View Articlehow to load booting image
i have downloaded image and copied to SD card please tell me how to load it into arm core
View ArticleMcASP AFIFO-EDMA not working for rx
Hi everyone:I'm working with the OMAP-L137/TMS320C6747 Floating Point Starter Kit from Spectrum Digital. The board has an TLV320AIC3106 Stereo Codec controlled via the McASP. I was transmitting and...
View ArticleHow do I see DSP cache config registers in memory browser?
Hello,From my DSP application code, I am writing to L2WWC (L2 Writeback Word Count Register Section) at address: 01844004h. But when I look at this region in the memory browser (using CCSv6, and the...
View Articletistdtypes.h giving compiler error when included in a C++ file
I was having a compiler error in a complicated project, so I created a SYS/BIOS "Typical" example and am seeing the same...
View ArticleAIS Boot Memory EMIFA CS3 Initialization
Is there syntax that allows you to initialize memory other than the pre-defined stuff like (PLL, EMIF CS2 Flash...)?I would like to initialize EMIFA CS3, but it appears I have to insert AIS Command(s)...
View ArticleReplacing from C6742 to C6748
Hi,I have a question about C6742 and C6748.On customer board, we are using C6742. But it seem that internal L2 RAM are not enough for the system.So, we are planning to replace the C6742 to C6748 which...
View ArticleOMAPL-138 UART Communication Problem
Hi, I am using OMAP-L138 EVK for my project. I am facing UART communication problem when I load uartEcho.c project of ARM processor. I found that UART communication channel is working fine when I...
View ArticleStarterware DDR test enhancement
OMAP-L138CCS 6.1.1Starterware 1.10.04.01All:In our board testing, we are using the ARM to test DDR memory prior to loading DSP code into it from NAND flash memory.There is an enhancement request to be...
View Articleregarding booting switches
Hai,What should be SW1 Configuration to boot linux from micro SD Slot , When i used with the following configuration 01111000, I got the output as there in the attachment but am unable to get VGA...
View ArticleUART interrupt stops working
We use the UART1 of an L138(DSP part) to communicate with a host PC (115200@8N1). Packets have 1kByte and are sent once a second to the PC and received about once a minute from the PC. The DSP of the...
View ArticleClik here to view.
Unable to get the IP address from TDA3x-evm
Dear all,I tried to use the network tools provided in Vision SDK 2.08.00. I followed the user guide of the Vision SDK network tools, chapter 1.2 (Finding IP address of the target EVM). The...
View Articleomap-L138 lcdk example code
I just bought the omap-L138 lcdk. Is there any example code that uses the ARM with DSP/BIOS and uses a .tcf to set it up? I cannot get ARM code to compile using a text configuration file (.tcf)
View ArticleClik here to view.
[AM1806] add garbage data in USB controller
Dear Champs,Is there any possibility to add garbage data(0xFB) in USB controller?In my customer's test, they found Invalid data(0xFB) was added after response NAK for IN Packets several times, and thus...
View ArticleClik here to view.
[C6746]Can same power supply be used for static 1.8V IO supplies and LVCMOS...
Dear Champs,Could you please let me know if same power supply can be used for All static 1.8V IO supplies(DVDD18, DDR_DVDD1.8, and USB0_VDD1.8) and all of the LVCMOS IO supply groups used at 1.8V...
View Article