Would like to get in touch with FAE associated with the TDA2x family of...
HiI would like to get in touch with the FAE associated with the TDA2x family of processors. I'm located in Los Angeles area.Thanks in advance,Wilberth
View ArticleClik here to view.
Face Detection Demo Program - Includes
Hi, After setting all the software tools (CCS v6.1, SYS/BIOS, etc) and testing the C674x LCDK platform with a SYS/BIOS program now I want to run the "Face Detection" demo project.I imported the...
View ArticleProblem with DSPLINK (readwrite sample) and EDMA
I am working with EVMOMAPL137. I want to customize the readwrite sample that use DSPLINK. I write a program on DSP side that use EDMA. If I configure and use the EDMA before DSPLINK initialization all...
View ArticleEDMA conflict with DSPLINK on EVMOMAPL137
I am working with EVMOMAPL137. I want to customize the readwrite sample that uses DSPLINK. I write a program on DSP side that use EDMA. If I configure and use the EDMA before DSPLINK initialization all...
View ArticleOMAPL137 DSP CORE BOOT CODE.
Hello All, Am using OMAPL137 in my project. Also, i have decided to work only on the DSP core(C674x) and am masking ARM9 core. I found the sample boot code to wake up the ARM9...
View ArticleClik here to view.
CCS device.h file errors
Hi Shankari, These were the errors which i have faced after building the project. So, please do let me know how do i solve this issue?? Waiting...
View ArticleClik here to view.
CCS V6 SEARCH OPTION IN WHOLE PROJECT
Hello All, Am working on OMAPL137 and am using CCS V6. So, i wanted to search a register name in the entire project and give me results. But, am not able to find the search option...
View ArticleOMAP-L137 : UART BOOT WITH 25MHz CLK source
To whom it may concern.Our customer would like to use 25MHz CLK with UART boot.Application note(sprab04g) mentioned input clock source of 24.000MHz is required but OMAP-L138 has some options for input...
View ArticleOMAPL138 SPI-EDMA
Hello, In my application I have two ADS8688 converters daisy chained to OMAPL138. To read ADCs I need to transfer 6Bytes. To read all 8 channels I need to do 8x6B transfers so that CS goes high between...
View ArticleClik here to view.
pins of the TMDXLCDK138 kit can not work
I have two TI's development boards, TMDXLCDK138. I wrote a module to configure the SPI0's CS , SIMO, SOMI, ENA pin as the GPIO pins . one board is normal. But another board's pins can not get the...
View ArticleOMAP L138 LCDK BOOT PROBLEM
Hi,I am trying to boot OMAP L138 LCDK.I boot it a few times,but now i am having a message;Setting up IP spoofing protection: rp_filterTue Apr 10 18:57:00 UTC 2012messages and then it stops.Can you help...
View ArticleUsing PSP BIOS driver for uPP
FPGA Spartan-6 is connected to DSP C6748 by uPP bus. FPGA creates the readiness signal which used to interrupt the DSP, i.e. DSP call to uPP driver to transfer data from FPGA into DSP.So, what the...
View ArticleAM3359: Regulator and Filter Functions
Hello,I'm searching Library functions which I can use for regulating (e.g. PI Regulator) and Filter function (e.g. FIR).Does TI have libraries for such functions and were can I find it? Best...
View ArticleList of API's for OMAPL137
Hello All, Am new to the TI family. Currently am using OMAPL137 controller for my project. I wanted to use SPI communication to interact with the other device. That other device is...
View ArticleDVDD18 Can Pull Up to 2.7V When Using Dual-Voltage IOs at 3.3V
Hi,I read in the errata sheet of OMAP L138 C600 that the DVDD18 supply can pull up to 2.7V When Using Dual-voltage IO at 3.3V. My customer use the TPS65070 to power the DSP L138 C6000, the banks...
View ArticleOMAPL138 EMDA3 concurrent transfer
We can see there are two CCs in OMAPL138 DSP core. I think they are physically independent of each other. But when I trigger a A-xfer DMA belongs to 0CC0 and a B-xfer DMA belongs to 1CC0 at a same...
View ArticleImplementing C6747 Sys/Bios USB driver
Hi. I need to implement USB on the C6747 EVM platform. The PC side will be the host. The aim is for the EVM to support a FAT file system.I am using latest CCS and SYS/BIOS versions. I am not booting...
View ArticleOMAPL-138 UART Problem
Hi,I am using OMAPL-138 LCDK.I want to use UART1 for my application.I made needed hardware modifications to enable UART1:Remove R205,R208Short R206,R209.I am programming with Linux OS.I still cannot...
View ArticleOMAPL138 clock speed
Hi,I would like to increase the CPU speed to maximum. Which is the easiest place to do it: uBoot, Linux, SYS/BIOS application's Platform.xdc or some other?risto
View ArticleI want to use the C6Flo at OMAP-L138 Development Kit (LCDK)
HelloI want to use the C6Flo at OMAP-L138 Development Kit (LCDK)Is this graphical development tool still support?Please tell me!
View Article