OMAP-L138: SPI related dought
Part Number:OMAP-L138Sir,I'm planning to use SPI for end device configuration. As it doesnot gives me any return data can I use the SPI MISO pin as GPIO for other purpose.In SPI peripheral :SPI MOSI,...
View ArticleRegarding Product Developement.
I am working on a design and developement of a Medical Product for POC (Proof of Concept) based on OMAP L138. Is there any standard or rules which will help me in design of the hardware Design and the...
View ArticleOMAPL138B-EP: An attempt to access the debug probe via USCIF ECOM has...
Part Number:OMAPL138B-EPHi,Iam using LCDKOMAPL138 and XDS200 for our new project.Iam facing some issue with the connection.When iam trying to connect LCDKOMAPL138 with XDS200 (using "Test connection"...
View ArticleOMAP-L138: CONTACT A SALES REPRESENTATIVE FOR SOUTH AMERICA
Part Number:OMAP-L138HELLO,I'm working on a university project that needs to adquire ultrasonic signals and send it to the PC via an RS232 serial interface Well I have been reading about the EVM that...
View ArticleOMAP-L138: SATA III compatability
Part Number:OMAP-L138hi,a cusotmer of mine makes telecommunication PBX (IP and normal Line).They have an issue with OMAP-L138, and it seems that due to bug in silicon OMAP do not support SATA III.As...
View ArticleRTOS/PROCESSOR-SDK-OMAPL138: Possible SDK Package Inconsistencies
Part Number:PROCESSOR-SDK-OMAPL138Tool/software:TI-RTOSCan someone confirm the following, as it is getting quite frustrating... Im not new to Linux, nor embedded systems... I am new to multicore...
View ArticleClik here to view.
RTOS/PROCESSOR-SDK-OMAPL138: Using make to Build IPC Examples
Part Number:PROCESSOR-SDK-OMAPL138Tool/software:TI-RTOSIm trying to follow the steps to build the provided IPC examplesIm not having any luck at all as the Makefile does not contain the required...
View ArticleRegarding Product Developement.
I am working on a design and developement of a Medical Product for POC (Proof of Concept) based on OMAP L138. Is there any standard or rules which will help me in design of the hardware Design and the...
View ArticleLinux/OMAP-L138: OMAP L-138 problem of writing a file
Part Number:OMAP-L138Tool/software: LinuxHelloI'm working in Linux in the AWM kernelI have a problemI have 2 applications. The first of them exchanges data with the DSP core via DSPLINK. The second one...
View ArticleOMAP-L138: How to burn a simple program to the flash
Part Number:OMAP-L138Hi,I'm trying to learn to use MityDSP-L138F, an evaluation board that uses TI's OMAP-L138. I don't know if this is the right place to ask for support, but I'll give it a try.I've...
View ArticleRTOS/OMAP-L138: Selection of DSP, target-OS, SDK and host-OS
Part Number:OMAP-L138Tool/software:TI-RTOSFor the development of a mobile audio device we need a high performance DSP with low power consumption and so the choice was made for a C674x core DSP, which...
View ArticleOMAP-L138: Where is output EPWM0 on OMAPL L138 LCDK?
Part Number:OMAP-L138Hi,Where is output EPWM0 on OMAPL L138 LCDK? According to the schematics, I know that EPWM1A and EPWM1B are located at Pins, J15.40 and J15.44, respectively. However, I cannot find...
View ArticleClik here to view.
Linux/LINUXSDK-OMAPL138: Can you give me a initial uImage of OMAPL138 LCDK...
Part Number:LINUXSDK-OMAPL138Tool/software: LinuxI bought a OMAPL138-LCDK development board from TI, after entering the development board system, because of my mistike I set up a root user's password,...
View ArticleOMAP-L138: Change initial output of eHRPWM to low logic
Part Number:OMAP-L138Hi,When I power on my OMAP L138 EVM, without initializing any parameters, the ehrPWM output (pin J15.44) is showing 3.3v on my oscilloscope. This indicates that the OMAP L138 LCDK,...
View ArticleOMAP-L137: OMAP-L137 Crystal Selection
Part Number:OMAP-L137The datasheet for the OMAP-L137 (page 61) states that for input clock frequencies between 20 and 30 MHz, a crystal with 60 ohm max ESR is recommended and typical load capacitance...
View ArticleOMAP-L138: Can't connect to the board through Ethernet
Part Number:OMAP-L138Hi,I have a MityDSP-L138F evaluation board, based on TI's Omap-L138 board.I'm running Windows 7 on my host PC (which also contains an Ubuntu guest OS on it). I'm able to...
View ArticlePROCESSOR-SDK-OMAPL138: u-boot and NAND
Part Number:PROCESSOR-SDK-OMAPL138I have been trying to load the various boot components into NAND from a u-boot terminal to allow booting from NAND. At the moment I'm manually punching in commands to...
View ArticleOMAP-L137: Unique Identifier
Part Number:OMAP-L137HelloIn many of our existing products we are using the OMAP-L137 CZKBA3 device.We are currently looking for way to get a unique identification of our products and though it might...
View ArticleRTOS/OMAPL138B-EP: Interrupt of EMDA is not trigger to OS
Part Number:OMAPL138B-EPTool/software:TI-RTOSI am developing application on OMAP L138 processor using EDMA, my OS is SYS/BIOS 6.45. I have met problem with trigger of interrupt of EDMA, when it's...
View ArticleOMAP-L138: Questions about ECC of NAND Flash
Part Number:OMAP-L138Hi,I was asked by OMAP-L138 from my customer.Please tell me about the read sequence of "20.2.5.6.6.2 4-Bit ECC" in the Technical Reference Manual.1. What is the reason why the...
View Article