how to generate toneRaw.h in OMAPL138_StarterWare_1_10_04_01 Demo Application?
how to generate toneRaw.h in OMAPL138_StarterWare_1_10_04_01 Demo Application?any detailed explaination of get the Hex Value From Wave File like belowunsigned short const toneRaw[] = {0x0512, 0x0605,...
View Articlegpio pins
i want to know port number and pin number of GPIO pins connected to J14 and J15 back side of LCDK 6748 board please share relevant doc
View ArticleOMAP-L138 device failure
We have currently build our Baseband board using OMAPL138 chipset. We have built around 100 boards. Initially the OMAPL138 was configured atr 300MHz with Core voltage of 1.2V. Recently we have...
View ArticleConfirmation of EMA_A pins for Starterware NAND Flash testing
OMAP-L138-EPCCS 6.xStarterware 1.10.04.01All:There is a new spin of a board coming my way that uses several pins normally associated with EMIFA. On this board, EMIFA is connected to NAND Flash (similar...
View ArticleSecure Kernel and Secure Boot Image Binding on OMAP-L138
Hi,i am running into some problems trying to implement our secure boot procedures for production.I am currently trying to use the Secure Kernel API to bind a firmware image to a device.For development...
View Articleerror :This makefile requires one of GNU make version 3.81 3.81beta1 3.90...
hello everyonei want to building DSPLink in one of stage, should to run : make -s but dont work and output error is: This makefile requires one of GNU make version 3.81 3.81beta1 3.90 3.92. Stop.so...
View ArticleHow do you determine the die rev for the OMAP-L138
We have some revB and revE dies and I need to tell them apart programmatically. The Die Identification registers aren't documented, is the die rev available in some other register or in ROM?
View ArticleLinux for an AM1705 custom board
Hello, I'm designing a custom board for the AM1705.The peripherals used are:Audio: TLV320AIC3106Ethernet: LAN8720aPower: TPS65023The memories used are:SPI Flash: K0XMFI011 (Spansion)Nand Flash:...
View ArticleClik here to view.
building dsplink - error: ‘IO_PHYS’ undeclared (first use in this function)
hello everyonei am building dsplink in one of step i shiuld run : make -sbut give out this error:please help me tnx
View ArticleuPP Digital Loopback EVMOMAPL138 failure
Hi,I am newbie in upp communication, may be anyone can help me to solve my problem. I try to modify upp example from LogicPD for EVMOMAPL138. I want to transmit signal by channel B and receive signal...
View ArticleDDR initialization failure on TI LCDKOMAPL138 board.
I failed to load my test code to my TI LCDKOMAPL138 board. see error message below. But I have not problem to load code to my Logic PD - Zoom™ OMAP-L138 eXperimenter Kit. both boards use OMAP-L138...
View ArticleMultiple I2C devices with Starterware
OMAP-L138-EPStarterware 1.10.04.01CCS 6.xAll:It looks like the Starterware examples assume a single slave for I2C. If multiple I2C devices are attached, would one need to alter the functions used so...
View ArticleSyslink examples hangs on Ipc_control with Ipc_CONTROLCMD_STARTCALLBACK
Syslink examples hangs on Ipc_control(remoteProcId, Ipc_CONTROLCMD_STARTCALLBACK, NULL). Syslink module is loaded with trace enabled, but prints no errors. Kernel command line is "<...>...
View ArticleClik here to view.
Generate square wave form for OMAP L138 LCDK
Dear All,We would like to generate the following square (or rectangular) wave form using OMAP L138 LCDK:We have previously tried ehrPWM module. Using this module we could generate the square wave,...
View Articleproblem in write permanent the code on the flash
i have a problem i try to burn the code using Spiwriter but the code doesn't work well,but when i debug using blackhawk the code works well
View ArticleIs there a StarterWare for OMAP-L137 ?
Hi!We are using an evaluation board EVMOMAP-L137 which features an OMAP-L137 Processor (DSP TMS320C6747 + ARM). We have found a good StarterWare software kit for CCS 6.0...
View ArticleC6748 SDRAM Corrupted
I am finding a small section of SDRAM (48 bytes) is getting corrupted. When execution reaches this location an exception occurs.I can view this memory in the Memory Browser and observe that it...
View ArticleNeed help to start writing program in C on TMS320LCDKC6748
Hello,I am a new user of TMS320LCDKC6748. I am working on DSP processor.In order to start programming on this board could you please help me to understand some basic C programs like Waveform...
View ArticleClik here to view.
[DA810] undershoot voltage level for input signal
HiMy customer has a question about the allowed undershoot voltage level for incoming signal on DA810. In the datasheet, there is a spec for output signal (Transient Overshoot/Undershoot) and that is...
View ArticleInsert 1 BIT Hamming ECC information in binary
We are using nand flash in out project and we have binary for the same. I want to insert ECC information in this binary and for that I have looked in different ti tools but not found any useful.There...
View Article