Clik here to view.
AM1808 sata issue
Hi guy;we met a issue about the AM1808 sata port. how can I make sure that the AM1808's sata PHY is broken?we have one board that can not detect the sata HDD(the same load in other borad work ok).here...
View ArticleOMAPLCDK GPIO LED Toggle not working but stays high all the time
Hi,Recently I bought an OMAPL138LCDK board from TI and I found the board was loaded with some Linux bootloader inside its NAND FLASH. So I made the boot switch changes for Emulation Debug support. (DIP...
View ArticleI/O Read Error on UartHost.exe for OMAPL137
Hello All, Am using OMAPL-137 on my custom board and able to get the BOOTME string on the hyperterminal when i boot it through UART1. So, now am trying the flash the .bin file to...
View ArticleClik here to view.
CCS installation for OMAP-L138 DSP+ARM9 development kit (LCDK)
I have downloaded the CCS (version 6.1.2.12) and started the installation. But I cannot find the C6x DSP + ARM processors option in the list (below is what is proposed)The target hardware is the...
View Articleindividuallly disabling OMAP-L138 peripherals
Hello,We have an application where we need to either disable unused OMAP-L138 peripherals, or else somehow explain that they won't interfere with normal operation.I have figured out how to disable most...
View ArticleOMAP L137 RAM disk File
Hello,I am trying to bring up OMAP L137 evm board. I have flashed DSP , ARM and Uboot bin files to the SPI flash. uboot works fine.I tried to copy kernel and RAM disk file to the SDRAM and board comes...
View ArticleWaiting for SFT on the OMAPL-137 when using sfh_OMAP_L137.exe
Hello All, Am using sfh_OMAP_L137.exe utility to flash the code to external flash device through UART. But, am facing the below issues.I have OMAPL_137 EVM board. In this board am...
View Articlesfh_OMAP-L137.exe Utility for flashing custom board connected to SPI1 Flash
Hello,We have made a custom board based on OMAPL137- HT and Flash is connected to SPI1.Can we use the same utility sfh_OMAP-L137.exe/UartHost.exe which are provided for OMAPL 137 evm.OR Can we suggest...
View ArticleOMAP LCDK starterware examples on vga
Hello there!I have the L138 LCDK board. I want to capture video data from a CMOS image sensor and store it to SD card. I was hoping to understand the code by looking at the vpif_loopback demo. But i...
View ArticleAM1808 high resolution timestamps
I am working on a project about time measurement on Lego Mindstorms Ev3. Lego used the AM1808 Chip.On the Mindstorms is running a modified Linux OS (Ev3dev).I want to measure some C code instructions...
View ArticleRequest for test project code CCS 3.3 for printing text on LCD (DA830 USER...
Hi All,Could someone send any test project code CCS 3.3 for printing text on LCD, which is a part of:DA830 USER INTERFACE MODULE (with OMAP-L137 EMV).Regards,Bartlomiej
View ArticleAutomatic use case generation exe not working for Version 02.08.00(Oct 2015)
Usecase generation tool i.e. vsdk_win32.exe in folder VISION_SDK_02_08_00_00\vision_sdk\tools\vision_sdk_usecase_gen\bin is not working. So we are unable to generate automatic usecase.The version is...
View ArticleProgramming PLL Controllers on OMAP-L1x8/C674x/AM18xx
All:When using the SYS_CLK_CALC_OMAP-L138_C674X_AM18X-v1p3.xls spreadsheet, it appears that a 50 MHz external square wave is not accepted (even though it is a valid option).However, to use the...
View ArticleClik here to view.
problem when writing data on emifa 8 bit from C6748 on OMAP L138 LCDK board
Hi there,Did anyone have this problem writing data on 8 bit EMIFA bus from C6748 ( on OMAPL138 LCDK board)?My emifa bus is using CS4. Basically, when writing data from 0x01 to 0xff in normal mode , I...
View ArticleOMAP-L138 Software Design Guide Updates
All:http://processors.wiki.ti.com/index.php/OMAP-L138_Software_Design_Guide is a great starting point, but here are a few updates that need to be added:1. Under "Software Hierarchy Providing specific...
View ArticleCode Composer Studio Flash Programming Plug-in for LCDK138 Nand Flash
All:Given that the LCDK138 (and other platforms) have external Nand Flash on the board, I request an enhancement to Code Composer Studio to support programming the NAND Flash from the CCS environment....
View ArticleMigrating from Starterware (OMAP-L138) on EVM to Target with OMAP-L138
All:Are there any specific guidelines for migrating from Starterware based on an EVM (in my case the LCDK138) to a OMAP-L138 based target?Here is a list of excellent sites I have...
View ArticleDSPLIB for OMAPL137
Hello, we are planning to use DSPLIB for FFT calculation of our application, and I was searching for suitable libraries.I could find below mentioned libraries,1) c674x-dsplib_1_03_00_012)...
View ArticleDigital Zoom
I apologize if this is not the appropriate forum to ask in (I couldn't find the thread for general processor questions).I'm looking for video chip that can create a digitally zoomed video, that is,...
View ArticlePRU TI C compiler documentation and control register access
HelloI'm developing an application for use on the OMAP L138's PRU and am having some trouble finding the correct documentation.I'm using CCS Version: 6.1.1.00022 and have installed the PRU Compiler...
View Article